BETAFPV Nano RF TX module is based on the ExpressLRS project, an open-source RC link for RC applications. ExpressLRS aims to achieve the best possible...
The Vista was fully authorized by DJI and compatible with their HD FPV System. Even better, the Caddx Vista was engineered to be lighter and smaller than the DJI Air Unit Module and also comes with mounting holes for easier installation onto your quad!
A single-camera module, which has a quick-release design for convenient replacement. The FPV camera does not come with a back cover or coaxial cables installed.Does not come with Air Unit Module. Cable not included, this is the camera only.
The FT5 5″ MKII Freestyle Drone by T-Motor features the DJI Airt Unit to bring you an immersive freestyle experience! Compared to the FT5 V.1 frame, the size of the tail has been increased to fully support the DJI Air Unit and parts.Choose between two KV options: 2400KV (4S), 1950KV (6S).
The Caddx Polar Micro Camera is an FPV camera with a mega starlight sensor. The Caddx Polar has a minimum 720p 60fps image transmission, with a transmission range of up to 4km and a minimum end-to-end latency within 32 ms. The camera is compatible with Vista and Air Unit modules.
Compared with F4 AIO 35A FC, F722 FC’s firmware is upgraded from F411 to F722, providing a better performance capability and higher calculation speed, which...
The CADDX VISTA KIT Micro Version is a replacement for the DJI Air Unit. With a micro-sized 19x19 camera, the Caddx Air Unit has all the features and performance of the original.The CADDX VISTA KIT features an ultra-low-latency high-definition digital image transmission, 1080p/60fps video recording, and eight frequency channels, allowing eight pilots to fly simultaneously.Compatible with DJI's Digital FPV Goggles, CADDX VISTA KIT (Digital VTX + HD FPV Camera) provides amazingly clear video, low latency, and even a built-in 1080P/60 FPS DVR.
Pavo30 whoop quadcopter, a new concept of 3-inch pusher drone developed by BETAFPV, is going further in performance, durability and power with brand new power system. It’s...
The Caddx Nebula Nano V2 Digital FPV Camera Kit is an advanced video transmission module that supports a 5.8GHz digital video signal and 720p 60fps image transmission.
Made in collaboration with one of the fastest FPV pilots in the world, MinChan Kim, the MCK 2207.5 V3 Motor from T-Motor is a fast-racing-motor made with premium components. Insanely smooth and extremely durable, the MCK 2207.5 V3 Motor is a racing motor aiming to be the best!Choose between two different KV options: 1910KV or 2100KV.
X-Knight 360 Carbon Frame Kit is an innovative, versatile and functional design frame that is is designed to work seamlessly with Insta ONE R Camera...
A replacement or spare antenna for the Caddx Vista Specifications Brand: Caddx FPV Variant: Standard 8cm / 15Cm Weight: 4 g Includes 1 x Caddx Vista...
On-board Ultra low noise 3.3V voltage regulator and RF filter for noise blocking
Features an additional front-end LNA for optimized performance and a front-end SAW filter for increased jamming immunity
Build-in embedded GNSS patch antenna, low power consumption
The 15 x 15 mm patch antenna provides the best compromise between the performance of a Right Hand Circular Polarized (RHCP) antenna and a small size to be integrated in any design.
Magnetic sensor QMC5883L integrated
Max navigation update rate
Single GNSS up to 18 Hz
2 Concurrent GNSS(GPS & GLONASS) up to 10 Hz
Horizontal position accuracy(GPS & GLONASS) 2.5 m CEP
Velocity accuracy 0.05m/s
Cold start 26 s
Aided cold starts: 2 s
Hot start 1 s
Beta95X V3 is perfectly suitable for the SMO 4K action camera. With a built-in camera mount and a power cable, it's very convenient for out-of-the-box installation and power input for the camera. Combining with SMO 4K, pilots can get a stable & high-quality video while in FPV flight.
Adopts a brand-new innovative pusher frame design, the frame is made of PA12 material, which has high abrasion resistance and can dampen noise & vibrations, bringing the drone a more durable flight and no fear of damage. The frame also comes with an EVA foam cushioning design to give you more safety flying.
Equipped with F4 AIO 20A Toothpick FC V4, 1106 3800KV motor, and D63 5-blade props, this highly efficient power system keeps Beta95X V3 more powerful and less noise in flight. For the battery, we highly recommend you using BETAFPV 450mAh 4S battery to get the best flying experience.
Centering the drone's gravity by reversed-motor design and top battery place makes the drone more maneuverable to achieve all FPV freestyle tricks such as diving.
Further improves the shock mitigation system to eliminate the shake of the camera, Beta95X V3 will make the camera more stable on the flight, which ensures pilots can capture all the beautiful moments of flight with the stabilized and clear video.
Flight time: About 4.5 min flight with 450mAh 4S battery
BETAFPV SMO 4K Camera
SMO 4K camera, a high-degree lightweight action camera for FPV drones that is developed by BETAFPV using Insta360 technology. SMO 4K camera only weighs 30g and perfectly fit for FPV drones, and brings pilots an extraordinary flying experience and a strong visual impact. What's more, it almost compatible with all kinds of FPV drones like micro cinewhoop Beta95X V3, 3-4in the ducted quad, 4-5in long-range FPV drone, and fixed-wing. It will be the perfect action camera for pilots in search of high-quality video with FPV racing drones.
Beta95X V3 Pusher Frame
A newly designed pusher whoop frame - Beta95X V3 Frame is made of high-quality PA12 material, which can dampen noise and vibrations and have high abrasion resistance, bringing the drone a more durable flight and no fear of damage. Meanwhile, it also comes with an EVA foam cushioning design to give you more safety flying. The pusher style puts all the cameras and batteries on the top of the platform, makes the center of gravity is right in the middle of the drone, brings the best fly operability.
Camera
Customized EOSV2 micro FPV camera is also provided on Beta95X V3 Whoop Quadcopter, brings a high-quality video and low RF interference.
FC & ESC
Beta95X V3 series whoop drone is equipped with the new released F4 20A AIO toothpick brushless FC, it extremely reduces the weight while improving the ability of the ESC to continuous current 20A, and brings pilots more power to fly the Beta95X V3 quad! Meanwhile, the new 20A FC V4 adds 2 pin connector ports for DJI Digital VTX and Rx, just plug & play, less solder work needed, super easy to install.
Motor & Props
Gemfan D63 5-Blades Props is designed for the inverted installation, and it brings pilots a smooth flight! Meanwhile, compared with D63 3-blades propellers, D63 5-blade props are more durable and more powerful, offers pilots a high-efficiency flight experience. Equipped with the 1106 3800KV Brushless Motor, it brings a stronger power and lower noise, which will give pilots an unprecedented flying experience.
The Beta95X V3 Whoop Quadcopter also comes with "props out" by default. Why we need "Props out" direction?
Default Betaflight props direction, quadcopter dips, and "washes out" in hard corners. With reversed props or "props out", no more dipping even in the hardest cornering.Know more about "Props Out".
FAQ
1. Cli Dump of Beta95X V3 Whoop Quadcopter (Click here to find the details.)
2. STL File for the Base of Naked Camera for Beta95X V3 Pusher Drone Series (Click here to find the details.)
3. How to power the Naked Camera on Beta95X V3 or Beta95X V3 HD Digital VTX.
One adapter 3P GH1.25 power cable for Customized Naked Camera is offered in the package, pilots can use it to power the Naked Camera.
Package
1 * Beta95X V3 Whoop Quadcopter
1 * Gemfan D63 5-blades Propellers(2CW+2CCW)
1 * 20mm FPV Camera Mount
1 * Spare EVA Foam Tape
1 * USB Adapter Board for FC
1 * Adapter Cable for Customized Naked Camera
Batteries and SMO 4K Camera are not included in the package. You can get it here for 450mAh 4S battery and SMO 4K camera.***Without VTX)***
Frame Diagram Link Roma F5 DJI Intro Roma F5 DJI Frame: Wheelbase :226mm Weight :135g Prop Siza :5 inch FC Mounting: 30.5×30.5(M3)&20×20mm(M2) Motor Mounting:16mm Top...
TAYCAN 25 Frame Kit Specification Frame Diagram Link Wheelbase :125mm Weight :86g Prop Siza :2.5 inch FC Mounting:20×20&25.5×25.5m(M2) Motor Mounting:9mm&12mm Top Plate 1.5mm Bottom Plate...
FETtec Spike Absorber well-selected TVS diodes to absorb dangerous voltage spikes to protect connected components designed for use with an electrolytic capacitor, which can be...
Features: Active current limiting @ 45A Input voltage: 3S-6S High quality 40V MOSFETs STM32G071 @ 64MHz 128 kHz Motor PWM Full sine wave control Soldering...
Features: Graphic OSD (STM32) Full KISS Tuning Filter (PIDs, Rates, Settings) LED control (RGB LED, Racewire) VTX Live data graphs (Voltage, motor rpm, current, motor...
The F60 Pro III continues the lineage of great FPV racing motors by T-Motor. The Pro III provides more thrust and increased durability compared to its predecessor.
The F60 Pro IV continues the lineage of great FPV racing motors by T-Motor. The Pro IV provides more thrust and increased durability compared to its predecessor.Equipped with high-temperature silver-core windings able to withstand up to 97C, after 100% throttle running 1 min. The overall stability of the motor has been enhanced. The threading has also been strengthened to prevent stripping or fracturing of the motor shaft. Each Pro IV motor is supplied with high-quality EZO bearings for maximum performance and lifespan. The new bell design looks amazing, while also providing the same non-slip propeller grip like the Pro III.
This mini camera provides some incredible specs for 1200TVL resolution and WDR worldwide. EOS2 is equipped with 1/3 CMOS sensor and 2.1mm lens with a 16:9 projection ratio.This camera is well suited to micro-structures that requires maximum weight and space Reduction without compromising quality.
FIRMWARE TARGET : MAMBA F722 (LEGACY) Diagram Link From Help Centre Link Note:Because STM32F722 heat large , please leave at least 5mm interspace at both sides of...
I want freestyle frame to show more performance in flight,a Super lightweight Freestyle frame,more convenient installation of electronic devices and more balanced center of gravity, so as to achieve better Smooth flight shooting, These ideas build the freestyle frame Mark4.
• Working noiselessly with excellent stability, fast response and high efficiency
• Easy to handle for both newbies and veterans
• Suitable for various frames for diverse demands
The T-Motor F55A 4-in-1 ESC is fully capable of pushing 6s with 75A burst and a sustained 55A current draw. Equipped with the latest in ESC technology such as 32-bit capability and BLHeli32 firmware.
T-Motor updated their F45 ESC with BLHeli_32 firmware. This tiny ESC packs 45A into an industrialized PCB layout made with premium features such as a 32bit main control chip, programmable LEDs, and BLHeli_32 firmware.
This ESC is T-Motor's 4-in-1 version of their popular F45A ESC. This 4-in-1 ESC packs 45A into an industrialized PCB layout made with premium features such as a 32bit main control chip, BLHeli_32 firmware, and 6s support.
POPO compatible propellers from Tiger Motors. These ultralight and thin bladed props are made for high kv motors and high speeds where they are most efficient.
This is a frame designed for Freestyle, called “Mark2”. After repeated design adjustment and testing, finally finished, let us present to you.
Although Mark2 is a regular rectangular frame, it still wants you to know its design features. A lot of mechanical shapes are added to the design, and the whole is very sexy and science fiction. The four arm and aluminum alloy parts are fixed, easy to replace the new machine arm, and the fixed performance is good. The camera position can be very good to protect the camera from damage
High-precision CNC aluminum alloy fixed parts, 3K full carbon fiber, 12.9 level YFS screw, give Mark2 to maintain strength advantage.
Enjoy Freestyle.
• Ultralight design with only 29.5g. Champion's choice for racing• High efficiency KV1600 runs well with 5”,6”,7”@4S-6S for long range flight• KV2400,KV2600 with high torque is extremely explosive & Efficient• Max Thrust: 1.62kg
GEP-GR2306 is the enamored production of our GEPRC. It passes our performance test in all aspects, and it can meet our extreme requirement on the parameter of the appearance of the electrical machine totally. Its elaborate appearance processing makes our eyes light up and we believe that the strong and steady power take-off will meet your expectation.
Our team keeps thinking that how to make a rack which is balanced both in competition and freestyle. Perhaps, GEP-KX5 can make you feel the good balance by its new and fresh design.GEP-KX5 is wished to be designed as a rack which is quite elegant and graceful. This is the reason why it is named as “Elegant”.
GEP-GR1408 motor is GEPRC’s newly developed brushless motor specially designed for 3inch propeller, a highly efficient and powerful motor, incorporating many new features and quality material throughout and is available in three versions - 3500kv, 3750K and 4100Kv to cater to the most demanding of flyers.
The GEP-GR1408 motor features a new streamlined motor shape, offering ultra-low wind resistance for fast forward flight and efficient heat dissipation. Incorporating high performance N52H curved magnets with a stator to magnet air-gap of only 0.15mm, the GEP-GR1408 motor is capable of high torque. High temperature resistance and low current resistant #180 enameled wire stator coil ensures stable power output throughout the throttle range and further enhanced by durable smooth running NSK Japanese bearings. The high precision CNC machined #7075 aluminum shaft increases crash durability of this motors while the large ventilation slots in the bell keeps the motor temperature low.
The GEP-GR1408 motor is optimized for 4S lipo and designed especially for 3inch propellers and when used with the GEPRC 3042 triblade propellers, it provides high output efficient performance. At only 15.2 g, the 4100Kv version generates an amazing 482g. The GEP-GR1408 motor is available in both CCC and CW threaded shaft.
GEP-IX5, is our new frame, called “Fairy”. 5 inch props, wheelbase is 200mm.
“Fairy” is suitable for racing, the “True X” structure, wheelbase only the 200mm, the 5 inch props.
Tail lights integrated 6 bright LED tail lights and the buzzer. LED tail lights support that FC (Betaflight / CleanFlight) control the color and the condition of the lights.
The biggest feature is in the nose of this frame, used the 3D TPU printing and the camera mount designed by 35 degree angle inclination. It can extremely reduce the wind resistance.