Material Toray T700 green carbon with silky coating Wheelbase 210mm Mouting hole 20×20/25.5×25.5 M2 Camera size 19x19mm Micro Size System Analog Cam/ HD Vista digital...
The Vista was fully authorized by DJI and compatible with their HD FPV System. Even better, the Caddx Vista was engineered to be lighter and smaller than the DJI Air Unit Module and also comes with mounting holes for easier installation onto your quad!
A single-camera module, which has a quick-release design for convenient replacement. The FPV camera does not come with a back cover or coaxial cables installed.Does not come with Air Unit Module. Cable not included, this is the camera only.
AD1 10A/100W Multi Function Intelligent Touch DUO Balance Charger/Discharger A series is a upgrade series which is designed for professional users with more...
The Caddx Polar Micro Camera is an FPV camera with a mega starlight sensor. The Caddx Polar has a minimum 720p 60fps image transmission, with a transmission range of up to 4km and a minimum end-to-end latency within 32 ms. The camera is compatible with Vista and Air Unit modules.
The CADDX VISTA KIT Micro Version is a replacement for the DJI Air Unit. With a micro-sized 19x19 camera, the Caddx Air Unit has all the features and performance of the original.The CADDX VISTA KIT features an ultra-low-latency high-definition digital image transmission, 1080p/60fps video recording, and eight frequency channels, allowing eight pilots to fly simultaneously.Compatible with DJI's Digital FPV Goggles, CADDX VISTA KIT (Digital VTX + HD FPV Camera) provides amazingly clear video, low latency, and even a built-in 1080P/60 FPS DVR.
The Caddx Nebula Nano V2 Digital FPV Camera Kit is an advanced video transmission module that supports a 5.8GHz digital video signal and 720p 60fps image transmission.
A replacement or spare antenna for the Caddx Vista Specifications Brand: Caddx FPV Variant: Standard 8cm / 15Cm Weight: 4 g Includes 1 x Caddx Vista...
Frame Diagram Link Roma F5 DJI Intro Roma F5 DJI Frame: Wheelbase :226mm Weight :135g Prop Siza :5 inch FC Mounting: 30.5×30.5(M3)&20×20mm(M2) Motor Mounting:16mm Top...
The best drone backpack for DJI Mavic series and foldable drones. Specially designed for the DJI Mavic series backpack turns easily from a daypack into...
TAYCAN 25 Frame Kit Specification Frame Diagram Link Wheelbase :125mm Weight :86g Prop Siza :2.5 inch FC Mounting:20×20&25.5×25.5m(M2) Motor Mounting:9mm&12mm Top Plate 1.5mm Bottom Plate...
This mini camera provides some incredible specs for 1200TVL resolution and WDR worldwide. EOS2 is equipped with 1/3 CMOS sensor and 2.1mm lens with a 16:9 projection ratio.This camera is well suited to micro-structures that requires maximum weight and space Reduction without compromising quality.
The OmniNXT F7 is Airbot’s top of the range flight controller based on the newly designed NXT architecture. It uses the trusty MPU6000 Gyro with an additional ICM20608 on top. With the onboard damping box, the gyros run perfectly under 32k looptime. If you haven't already seen it, you should check out Josh's awesome video on different IMUs. The NXT also comes with 2 different BECs and 6 UARTs.
FIRMWARE TARGET : MAMBA F722 (LEGACY) Diagram Link From Help Centre Link Note:Because STM32F722 heat large , please leave at least 5mm interspace at both sides of...
I want freestyle frame to show more performance in flight,a Super lightweight Freestyle frame,more convenient installation of electronic devices and more balanced center of gravity, so as to achieve better Smooth flight shooting, These ideas build the freestyle frame Mark4.
The Omnibus Fireworks flight controller uses the ICM20608 over SPI for the best possible flight performance. With onboard damping box, the ICM20608 runs perfectly under 32k Gyro loop. If you haven't already seen it, you should check out Josh's awesome video on different IMUs. Also onboard are a barometer and AB7456 OSD chip for the BetaFlight integrated OSD.
This is a frame designed for Freestyle, called “Mark2”. After repeated design adjustment and testing, finally finished, let us present to you.
Although Mark2 is a regular rectangular frame, it still wants you to know its design features. A lot of mechanical shapes are added to the design, and the whole is very sexy and science fiction. The four arm and aluminum alloy parts are fixed, easy to replace the new machine arm, and the fixed performance is good. The camera position can be very good to protect the camera from damage
High-precision CNC aluminum alloy fixed parts, 3K full carbon fiber, 12.9 level YFS screw, give Mark2 to maintain strength advantage.
Enjoy Freestyle.