Material Toray T700 green carbon with silky coating Wheelbase 210mm Mouting hole 20×20/25.5×25.5 M2 Camera size 19x19mm Micro Size System Analog Cam/ HD Vista digital...
The Vista was fully authorized by DJI and compatible with their HD FPV System. Even better, the Caddx Vista was engineered to be lighter and smaller than the DJI Air Unit Module and also comes with mounting holes for easier installation onto your quad!
A single-camera module, which has a quick-release design for convenient replacement. The FPV camera does not come with a back cover or coaxial cables installed.Does not come with Air Unit Module. Cable not included, this is the camera only.
AD1 10A/100W Multi Function Intelligent Touch DUO Balance Charger/Discharger A series is a upgrade series which is designed for professional users with more...
The Caddx Polar Micro Camera is an FPV camera with a mega starlight sensor. The Caddx Polar has a minimum 720p 60fps image transmission, with a transmission range of up to 4km and a minimum end-to-end latency within 32 ms. The camera is compatible with Vista and Air Unit modules.
The CADDX VISTA KIT Micro Version is a replacement for the DJI Air Unit. With a micro-sized 19x19 camera, the Caddx Air Unit has all the features and performance of the original.The CADDX VISTA KIT features an ultra-low-latency high-definition digital image transmission, 1080p/60fps video recording, and eight frequency channels, allowing eight pilots to fly simultaneously.Compatible with DJI's Digital FPV Goggles, CADDX VISTA KIT (Digital VTX + HD FPV Camera) provides amazingly clear video, low latency, and even a built-in 1080P/60 FPS DVR.
The Caddx Nebula Nano V2 Digital FPV Camera Kit is an advanced video transmission module that supports a 5.8GHz digital video signal and 720p 60fps image transmission.
A replacement or spare antenna for the Caddx Vista Specifications Brand: Caddx FPV Variant: Standard 8cm / 15Cm Weight: 4 g Includes 1 x Caddx Vista...
Description:
Smale in size
Built in voltage cheker
XT30 and Barrel output connectors
Specifications:
Capacity: 3000mAh 2S1P
Voltage: 7.4V
Net Weight: 106Gr
Connector: DC5.5 and XT30
Size: 63*40*20mm
Package Includes:
1 x Infinity 3000mAh Li-Po Goggle Battery
On-board Ultra low noise 3.3V voltage regulator and RF filter for noise blocking
Features an additional front-end LNA for optimized performance and a front-end SAW filter for increased jamming immunity
Build-in embedded GNSS patch antenna, low power consumption
The 15 x 15 mm patch antenna provides the best compromise between the performance of a Right Hand Circular Polarized (RHCP) antenna and a small size to be integrated in any design.
Magnetic sensor QMC5883L integrated
Max navigation update rate
Single GNSS up to 18 Hz
2 Concurrent GNSS(GPS & GLONASS) up to 10 Hz
Horizontal position accuracy(GPS & GLONASS) 2.5 m CEP
Velocity accuracy 0.05m/s
Cold start 26 s
Aided cold starts: 2 s
Hot start 1 s
Frame Diagram Link Roma F5 DJI Intro Roma F5 DJI Frame: Wheelbase :226mm Weight :135g Prop Siza :5 inch FC Mounting: 30.5×30.5(M3)&20×20mm(M2) Motor Mounting:16mm Top...
TAYCAN 25 Frame Kit Specification Frame Diagram Link Wheelbase :125mm Weight :86g Prop Siza :2.5 inch FC Mounting:20×20&25.5×25.5m(M2) Motor Mounting:9mm&12mm Top Plate 1.5mm Bottom Plate...
FETtec Spike Absorber well-selected TVS diodes to absorb dangerous voltage spikes to protect connected components designed for use with an electrolytic capacitor, which can be...
Features: Active current limiting @ 45A Input voltage: 3S-6S High quality 40V MOSFETs STM32G071 @ 64MHz 128 kHz Motor PWM Full sine wave control Soldering...
Features: Graphic OSD (STM32) Full KISS Tuning Filter (PIDs, Rates, Settings) LED control (RGB LED, Racewire) VTX Live data graphs (Voltage, motor rpm, current, motor...
This mini camera provides some incredible specs for 1200TVL resolution and WDR worldwide. EOS2 is equipped with 1/3 CMOS sensor and 2.1mm lens with a 16:9 projection ratio.This camera is well suited to micro-structures that requires maximum weight and space Reduction without compromising quality.
The OmniNXT F7 is Airbot’s top of the range flight controller based on the newly designed NXT architecture. It uses the trusty MPU6000 Gyro with an additional ICM20608 on top. With the onboard damping box, the gyros run perfectly under 32k looptime. If you haven't already seen it, you should check out Josh's awesome video on different IMUs. The NXT also comes with 2 different BECs and 6 UARTs.
FIRMWARE TARGET : MAMBA F722 (LEGACY) Diagram Link From Help Centre Link Note:Because STM32F722 heat large , please leave at least 5mm interspace at both sides of...
I want freestyle frame to show more performance in flight,a Super lightweight Freestyle frame,more convenient installation of electronic devices and more balanced center of gravity, so as to achieve better Smooth flight shooting, These ideas build the freestyle frame Mark4.
Here is another super affordable package added to our 1S batteries to make those indoor race session even more fun.Fits Emax Tinyhawk, Mobula 7 and similar frames.Package includes:5 x Infinity 1S 450mAh 85C HIGH VOLTAGE Specifications:3.8V-4.35V 450mAh 1S 85C/170C Lipo BatteryCapacity:...
Description After the huge success of the 1550 100C, Infinity introduces their next power house 1550mAh 120C continuous and 240C Burst pack. Description: Brand name:...
The Omnibus Fireworks flight controller uses the ICM20608 over SPI for the best possible flight performance. With onboard damping box, the ICM20608 runs perfectly under 32k Gyro loop. If you haven't already seen it, you should check out Josh's awesome video on different IMUs. Also onboard are a barometer and AB7456 OSD chip for the BetaFlight integrated OSD.
This is a frame designed for Freestyle, called “Mark2”. After repeated design adjustment and testing, finally finished, let us present to you.
Although Mark2 is a regular rectangular frame, it still wants you to know its design features. A lot of mechanical shapes are added to the design, and the whole is very sexy and science fiction. The four arm and aluminum alloy parts are fixed, easy to replace the new machine arm, and the fixed performance is good. The camera position can be very good to protect the camera from damage
High-precision CNC aluminum alloy fixed parts, 3K full carbon fiber, 12.9 level YFS screw, give Mark2 to maintain strength advantage.
Enjoy Freestyle.
GEP-GR2306 is the enamored production of our GEPRC. It passes our performance test in all aspects, and it can meet our extreme requirement on the parameter of the appearance of the electrical machine totally. Its elaborate appearance processing makes our eyes light up and we believe that the strong and steady power take-off will meet your expectation.
Our team keeps thinking that how to make a rack which is balanced both in competition and freestyle. Perhaps, GEP-KX5 can make you feel the good balance by its new and fresh design.GEP-KX5 is wished to be designed as a rack which is quite elegant and graceful. This is the reason why it is named as “Elegant”.