The Vista was fully authorized by DJI and compatible with their HD FPV System. Even better, the Caddx Vista was engineered to be lighter and smaller than the DJI Air Unit Module and also comes with mounting holes for easier installation onto your quad!
A single-camera module, which has a quick-release design for convenient replacement. The FPV camera does not come with a back cover or coaxial cables installed.Does not come with Air Unit Module. Cable not included, this is the camera only.
AD1 10A/100W Multi Function Intelligent Touch DUO Balance Charger/Discharger A series is a upgrade series which is designed for professional users with more...
The Caddx Polar Micro Camera is an FPV camera with a mega starlight sensor. The Caddx Polar has a minimum 720p 60fps image transmission, with a transmission range of up to 4km and a minimum end-to-end latency within 32 ms. The camera is compatible with Vista and Air Unit modules.
PRODUCT DETAILS Introducing the Hyperlite Freerange 5” LR Freestyle frame! This frame is a culmination of months of extensive testing by our team and our...
The CADDX VISTA KIT Micro Version is a replacement for the DJI Air Unit. With a micro-sized 19x19 camera, the Caddx Air Unit has all the features and performance of the original.The CADDX VISTA KIT features an ultra-low-latency high-definition digital image transmission, 1080p/60fps video recording, and eight frequency channels, allowing eight pilots to fly simultaneously.Compatible with DJI's Digital FPV Goggles, CADDX VISTA KIT (Digital VTX + HD FPV Camera) provides amazingly clear video, low latency, and even a built-in 1080P/60 FPS DVR.
It's race ready with PitMode, a super-clean and interference free power levels, and connectivity to flight controllers and other means of quickly changing channels. It runs off a filtered 5V power supply, so it's perfect when being connected to a TBS CORE PRO or TBS PowerCube (*)
As builds become smaller and the innovation surrounding brushed and brushless micro quads accelerates, the need for a high-quality VTx increases. TBS has built the smallest VTx possible, focusing purely on size! Sporting the usual Unify Pro pedigree, a newly-revised u.FL connector and the industry-standard Smart Audio support. You will be blown away with the performance in terms of range, signal clarity and signal spacing.
Distilling the smallest, lightest and most powerful video transmitters (aka "the golden standard" :) ) down to a bare minimum for FPV racing, at a very attractive price!
The Caddx Nebula Nano V2 Digital FPV Camera Kit is an advanced video transmission module that supports a 5.8GHz digital video signal and 720p 60fps image transmission.
The SOURCE PODRACER is a ultralight racing frame, made for speed addicts and grassroots fpv racers. It is designed to maximize speed and minimize drag. It fits and protects all the current toothpick-style FPV components and is optimized for light weight. The SOURCE PODRACER is your perfect race winner, and is recommended for pro racing pilots only.
The SOURCE ONE is a wide-stance X configuration frame, popular for freestyle or free-range acrobatic flying. It is built to withstand harsh crashes and abuse. It fits and protects all the classic FPV components and is optimized for light weight. The SOURCE ONE is a perfect everyday workhorse for casual FPV flying and competitive freestyle.
1. 360 degree rotation, stable clamping 2.Suitable for all kinds of flat tabletops, suction cup is more stable with water adsorption 3. Plastic card slot,...
Clamp Steel PCB Board Soldering Holder 1.Universal holder for mobile phone repair. 2.Simple operation, precision screw positioning. 3.Three pieces bayonet can be moved, you can...
Description: XT60 Connector 1-Male 2-Female Serial Connection Cable Total length: 11cm Wire: silicon wire 14AWG Connectors: 1 male and 2 female connectors in SERIAL connection...
Multi-function wire:8 in 1 one side:4.0MM golden connector length:300MM Main wire : 14AWG red /black silicone wire 150MM with Male 4.0MM banana connector . Branch...
Specifications: 6 flexible arms each with a large swiveling alligator clip. 6+1 pockets in beautifully base to hold loose components. 6 Silicon clip tips...
A replacement or spare antenna for the Caddx Vista Specifications Brand: Caddx FPV Variant: Standard 8cm / 15Cm Weight: 4 g Includes 1 x Caddx Vista...
The HGLRC Forward 65A 4-in-1 ESC brings serious power to the 30.5x30.5 game. 3-6S capable and stackable with other mini FC's, this ESC gives you great specs in a tiny package.
Frame Diagram Link Roma F5 DJI Intro Roma F5 DJI Frame: Wheelbase :226mm Weight :135g Prop Siza :5 inch FC Mounting: 30.5×30.5(M3)&20×20mm(M2) Motor Mounting:16mm Top...
The best drone backpack for DJI Mavic series and foldable drones. Specially designed for the DJI Mavic series backpack turns easily from a daypack into...
TAYCAN 25 Frame Kit Specification Frame Diagram Link Wheelbase :125mm Weight :86g Prop Siza :2.5 inch FC Mounting:20×20&25.5×25.5m(M2) Motor Mounting:9mm&12mm Top Plate 1.5mm Bottom Plate...
*BNF/PNP Version Include: HGLRC Sector 5 V3 Freestyle FPV Racing Drone Net Weight:442.4g(Weight without receiver) Sector 5 V3 Freestyle Frame 5 inch Type:5″ frame Wheelbase:218mm...
This mini camera provides some incredible specs for 1200TVL resolution and WDR worldwide. EOS2 is equipped with 1/3 CMOS sensor and 2.1mm lens with a 16:9 projection ratio.This camera is well suited to micro-structures that requires maximum weight and space Reduction without compromising quality.
The OmniNXT F7 is Airbot’s top of the range flight controller based on the newly designed NXT architecture. It uses the trusty MPU6000 Gyro with an additional ICM20608 on top. With the onboard damping box, the gyros run perfectly under 32k looptime. If you haven't already seen it, you should check out Josh's awesome video on different IMUs. The NXT also comes with 2 different BECs and 6 UARTs.
FIRMWARE TARGET : MAMBA F722 (LEGACY) Diagram Link From Help Centre Link Note:Because STM32F722 heat large , please leave at least 5mm interspace at both sides of...
I want freestyle frame to show more performance in flight,a Super lightweight Freestyle frame,more convenient installation of electronic devices and more balanced center of gravity, so as to achieve better Smooth flight shooting, These ideas build the freestyle frame Mark4.
This is a light weight drone racing frame.The goal of this quadcopter frame was low drag, low weight, high durability, extremely high serviceability, reasonable component protection and low cost frame and parts.
The revolution in circular 5.8 GHz technology. Hand-tuned for ultimate noise and reflection rejection. True circularity and great range. Designed by none other than IBCrazy. SMA version.
The Immortal T is a new creation for all the hardcore racers and freestylers out there that have grown to love the TBS Crossfire. It survives prop strikes without breaking a sweat and mounts perfectly to your frames! Tested by the world's leading freestyle pilots, it has their "seal of approval"
A slightly-directional antenna for best signal penetration. Built ultra-durable using lessons learned from TBS Triumph, and designed by none other than IBCrazy!
TS100 employs 304 stainless steel nested shell of Polycarbonate plastic. It is designed with safety circuit and anti-static structure, integrated with DC5525 12-24V port, dual-temperature sensors and accelerated sensors with STM32 chip. Under these functionalities, temperature can be controlled accurately, stably and easily adjusted from 100°C to 400°C, and the TS100 also has sleep mode and automatic over-heating warning.
The Omnibus Fireworks flight controller uses the ICM20608 over SPI for the best possible flight performance. With onboard damping box, the ICM20608 runs perfectly under 32k Gyro loop. If you haven't already seen it, you should check out Josh's awesome video on different IMUs. Also onboard are a barometer and AB7456 OSD chip for the BetaFlight integrated OSD.
F5 - this 5 inch freestyle Frame design by Oren Elimor (Mechanical engineer & freestyle pilot) in cooperation with Israeli top free style pilots to be on the cutting edge of drone technology.
This is a frame designed for Freestyle, called “Mark2”. After repeated design adjustment and testing, finally finished, let us present to you.
Although Mark2 is a regular rectangular frame, it still wants you to know its design features. A lot of mechanical shapes are added to the design, and the whole is very sexy and science fiction. The four arm and aluminum alloy parts are fixed, easy to replace the new machine arm, and the fixed performance is good. The camera position can be very good to protect the camera from damage
High-precision CNC aluminum alloy fixed parts, 3K full carbon fiber, 12.9 level YFS screw, give Mark2 to maintain strength advantage.
Enjoy Freestyle.
GEP-GR2306 is the enamored production of our GEPRC. It passes our performance test in all aspects, and it can meet our extreme requirement on the parameter of the appearance of the electrical machine totally. Its elaborate appearance processing makes our eyes light up and we believe that the strong and steady power take-off will meet your expectation.
Our team keeps thinking that how to make a rack which is balanced both in competition and freestyle. Perhaps, GEP-KX5 can make you feel the good balance by its new and fresh design.GEP-KX5 is wished to be designed as a rack which is quite elegant and graceful. This is the reason why it is named as “Elegant”.