AD1 10A/100W Multi Function Intelligent Touch DUO Balance Charger/Discharger A series is a upgrade series which is designed for professional users with more...
Radiolink Pixhawk is a real king of the open source flight controller made by Radiolink. On the basis of 3DR PIX function, it developes optimized circuit design and creative design automation software QA system, which guarantee the quality of product.
Description:
Smale in size
Built in voltage cheker
XT30 and Barrel output connectors
Specifications:
Capacity: 3000mAh 2S1P
Voltage: 7.4V
Net Weight: 106Gr
Connector: DC5.5 and XT30
Size: 63*40*20mm
Package Includes:
1 x Infinity 3000mAh Li-Po Goggle Battery
On-board Ultra low noise 3.3V voltage regulator and RF filter for noise blocking
Features an additional front-end LNA for optimized performance and a front-end SAW filter for increased jamming immunity
Build-in embedded GNSS patch antenna, low power consumption
The 15 x 15 mm patch antenna provides the best compromise between the performance of a Right Hand Circular Polarized (RHCP) antenna and a small size to be integrated in any design.
Magnetic sensor QMC5883L integrated
Max navigation update rate
Single GNSS up to 18 Hz
2 Concurrent GNSS(GPS & GLONASS) up to 10 Hz
Horizontal position accuracy(GPS & GLONASS) 2.5 m CEP
Velocity accuracy 0.05m/s
Cold start 26 s
Aided cold starts: 2 s
Hot start 1 s
The HGLRC Forward 65A 4-in-1 ESC brings serious power to the 30.5x30.5 game. 3-6S capable and stackable with other mini FC's, this ESC gives you great specs in a tiny package.
FETtec Spike Absorber well-selected TVS diodes to absorb dangerous voltage spikes to protect connected components designed for use with an electrolytic capacitor, which can be...
Features: Active current limiting @ 45A Input voltage: 3S-6S High quality 40V MOSFETs STM32G071 @ 64MHz 128 kHz Motor PWM Full sine wave control Soldering...
Features: Graphic OSD (STM32) Full KISS Tuning Filter (PIDs, Rates, Settings) LED control (RGB LED, Racewire) VTX Live data graphs (Voltage, motor rpm, current, motor...
*BNF/PNP Version Include: HGLRC Sector 5 V3 Freestyle FPV Racing Drone Net Weight:442.4g(Weight without receiver) Sector 5 V3 Freestyle Frame 5 inch Type:5″ frame Wheelbase:218mm...
The OmniNXT F7 is Airbot’s top of the range flight controller based on the newly designed NXT architecture. It uses the trusty MPU6000 Gyro with an additional ICM20608 on top. With the onboard damping box, the gyros run perfectly under 32k looptime. If you haven't already seen it, you should check out Josh's awesome video on different IMUs. The NXT also comes with 2 different BECs and 6 UARTs.
I want freestyle frame to show more performance in flight,a Super lightweight Freestyle frame,more convenient installation of electronic devices and more balanced center of gravity, so as to achieve better Smooth flight shooting, These ideas build the freestyle frame Mark4.
Here is another super affordable package added to our 1S batteries to make those indoor race session even more fun.Fits Emax Tinyhawk, Mobula 7 and similar frames.Package includes:5 x Infinity 1S 450mAh 85C HIGH VOLTAGE Specifications:3.8V-4.35V 450mAh 1S 85C/170C Lipo BatteryCapacity:...
Description After the huge success of the 1550 100C, Infinity introduces their next power house 1550mAh 120C continuous and 240C Burst pack. Description: Brand name:...
The Omnibus Fireworks flight controller uses the ICM20608 over SPI for the best possible flight performance. With onboard damping box, the ICM20608 runs perfectly under 32k Gyro loop. If you haven't already seen it, you should check out Josh's awesome video on different IMUs. Also onboard are a barometer and AB7456 OSD chip for the BetaFlight integrated OSD.
This is a frame designed for Freestyle, called “Mark2”. After repeated design adjustment and testing, finally finished, let us present to you.
Although Mark2 is a regular rectangular frame, it still wants you to know its design features. A lot of mechanical shapes are added to the design, and the whole is very sexy and science fiction. The four arm and aluminum alloy parts are fixed, easy to replace the new machine arm, and the fixed performance is good. The camera position can be very good to protect the camera from damage
High-precision CNC aluminum alloy fixed parts, 3K full carbon fiber, 12.9 level YFS screw, give Mark2 to maintain strength advantage.
Enjoy Freestyle.
GEP-GR2306 is the enamored production of our GEPRC. It passes our performance test in all aspects, and it can meet our extreme requirement on the parameter of the appearance of the electrical machine totally. Its elaborate appearance processing makes our eyes light up and we believe that the strong and steady power take-off will meet your expectation.
Our team keeps thinking that how to make a rack which is balanced both in competition and freestyle. Perhaps, GEP-KX5 can make you feel the good balance by its new and fresh design.GEP-KX5 is wished to be designed as a rack which is quite elegant and graceful. This is the reason why it is named as “Elegant”.