Material Toray T700 green carbon with silky coating Wheelbase 210mm Mouting hole 20×20/25.5×25.5 M2 Camera size 19x19mm Micro Size System Analog Cam/ HD Vista digital...
The Vista was fully authorized by DJI and compatible with their HD FPV System. Even better, the Caddx Vista was engineered to be lighter and smaller than the DJI Air Unit Module and also comes with mounting holes for easier installation onto your quad!
A single-camera module, which has a quick-release design for convenient replacement. The FPV camera does not come with a back cover or coaxial cables installed.Does not come with Air Unit Module. Cable not included, this is the camera only.
The Caddx Polar Micro Camera is an FPV camera with a mega starlight sensor. The Caddx Polar has a minimum 720p 60fps image transmission, with a transmission range of up to 4km and a minimum end-to-end latency within 32 ms. The camera is compatible with Vista and Air Unit modules.
Enhance your UAV fleet with Precision Landing and target recognition features. Attach the IR-LOCK Sensor to your UAV, and place the MarkOne Beacon where you want to land. Great...
The CADDX VISTA KIT Micro Version is a replacement for the DJI Air Unit. With a micro-sized 19x19 camera, the Caddx Air Unit has all the features and performance of the original.The CADDX VISTA KIT features an ultra-low-latency high-definition digital image transmission, 1080p/60fps video recording, and eight frequency channels, allowing eight pilots to fly simultaneously.Compatible with DJI's Digital FPV Goggles, CADDX VISTA KIT (Digital VTX + HD FPV Camera) provides amazingly clear video, low latency, and even a built-in 1080P/60 FPS DVR.
The Caddx Nebula Nano V2 Digital FPV Camera Kit is an advanced video transmission module that supports a 5.8GHz digital video signal and 720p 60fps image transmission.
A replacement or spare antenna for the Caddx Vista Specifications Brand: Caddx FPV Variant: Standard 8cm / 15Cm Weight: 4 g Includes 1 x Caddx Vista...
On-board Ultra low noise 3.3V voltage regulator and RF filter for noise blocking
Features an additional front-end LNA for optimized performance and a front-end SAW filter for increased jamming immunity
Build-in embedded GNSS patch antenna, low power consumption
The 15 x 15 mm patch antenna provides the best compromise between the performance of a Right Hand Circular Polarized (RHCP) antenna and a small size to be integrated in any design.
Magnetic sensor QMC5883L integrated
Max navigation update rate
Single GNSS up to 18 Hz
2 Concurrent GNSS(GPS & GLONASS) up to 10 Hz
Horizontal position accuracy(GPS & GLONASS) 2.5 m CEP
Velocity accuracy 0.05m/s
Cold start 26 s
Aided cold starts: 2 s
Hot start 1 s
The HGLRC Forward 65A 4-in-1 ESC brings serious power to the 30.5x30.5 game. 3-6S capable and stackable with other mini FC's, this ESC gives you great specs in a tiny package.
Herelink AccessoriesHerelink is an all-in-one solution for long-range HD video transmission, which can realize video, data transmission and radio control. The 2.4GHz radio controller with built-in screen...
*BNF/PNP Version Include: HGLRC Sector 5 V3 Freestyle FPV Racing Drone Net Weight:442.4g(Weight without receiver) Sector 5 V3 Freestyle Frame 5 inch Type:5″ frame Wheelbase:218mm...
Mini Carrier Board has the standardized DF17 connector which allows user to connect it to every version of the Cube flight controller. With smaller size...
This mini camera provides some incredible specs for 1200TVL resolution and WDR worldwide. EOS2 is equipped with 1/3 CMOS sensor and 2.1mm lens with a 16:9 projection ratio.This camera is well suited to micro-structures that requires maximum weight and space Reduction without compromising quality.
The OmniNXT F7 is Airbot’s top of the range flight controller based on the newly designed NXT architecture. It uses the trusty MPU6000 Gyro with an additional ICM20608 on top. With the onboard damping box, the gyros run perfectly under 32k looptime. If you haven't already seen it, you should check out Josh's awesome video on different IMUs. The NXT also comes with 2 different BECs and 6 UARTs.
I want freestyle frame to show more performance in flight,a Super lightweight Freestyle frame,more convenient installation of electronic devices and more balanced center of gravity, so as to achieve better Smooth flight shooting, These ideas build the freestyle frame Mark4.
Get Started on your road to Autonomy! This Kit contains the following items The Cube…. the brains behind the opperation. A standard carrier board.(no compatible...
INSIDE THE CUBE An STM32F427 Rev 3 Flight management unit. (where the flight controller lives.) An STM32F100 I/O processor with pass through capabilities for...
Cube Yellow target to education, drones lovers and professional cost-effective flight control hardware providers. The new generation of more powerful F7 processor, stronger performance, faster,...
What’s inside Here+ RTK Base & HERE 3 (M8P) Combo (Separated products) Highlights Centimeter‑level GNSS positioning for the mass market Integrated Real Time Kinematics (RTK)...
The Omnibus Fireworks flight controller uses the ICM20608 over SPI for the best possible flight performance. With onboard damping box, the ICM20608 runs perfectly under 32k Gyro loop. If you haven't already seen it, you should check out Josh's awesome video on different IMUs. Also onboard are a barometer and AB7456 OSD chip for the BetaFlight integrated OSD.
This is a frame designed for Freestyle, called “Mark2”. After repeated design adjustment and testing, finally finished, let us present to you.
Although Mark2 is a regular rectangular frame, it still wants you to know its design features. A lot of mechanical shapes are added to the design, and the whole is very sexy and science fiction. The four arm and aluminum alloy parts are fixed, easy to replace the new machine arm, and the fixed performance is good. The camera position can be very good to protect the camera from damage
High-precision CNC aluminum alloy fixed parts, 3K full carbon fiber, 12.9 level YFS screw, give Mark2 to maintain strength advantage.
Enjoy Freestyle.
GEP-GR2306 is the enamored production of our GEPRC. It passes our performance test in all aspects, and it can meet our extreme requirement on the parameter of the appearance of the electrical machine totally. Its elaborate appearance processing makes our eyes light up and we believe that the strong and steady power take-off will meet your expectation.
Our team keeps thinking that how to make a rack which is balanced both in competition and freestyle. Perhaps, GEP-KX5 can make you feel the good balance by its new and fresh design.GEP-KX5 is wished to be designed as a rack which is quite elegant and graceful. This is the reason why it is named as “Elegant”.
GEP-GR1408 motor is GEPRC’s newly developed brushless motor specially designed for 3inch propeller, a highly efficient and powerful motor, incorporating many new features and quality material throughout and is available in three versions - 3500kv, 3750K and 4100Kv to cater to the most demanding of flyers.
The GEP-GR1408 motor features a new streamlined motor shape, offering ultra-low wind resistance for fast forward flight and efficient heat dissipation. Incorporating high performance N52H curved magnets with a stator to magnet air-gap of only 0.15mm, the GEP-GR1408 motor is capable of high torque. High temperature resistance and low current resistant #180 enameled wire stator coil ensures stable power output throughout the throttle range and further enhanced by durable smooth running NSK Japanese bearings. The high precision CNC machined #7075 aluminum shaft increases crash durability of this motors while the large ventilation slots in the bell keeps the motor temperature low.
The GEP-GR1408 motor is optimized for 4S lipo and designed especially for 3inch propellers and when used with the GEPRC 3042 triblade propellers, it provides high output efficient performance. At only 15.2 g, the 4100Kv version generates an amazing 482g. The GEP-GR1408 motor is available in both CCC and CW threaded shaft.
GEP-IX5, is our new frame, called “Fairy”. 5 inch props, wheelbase is 200mm.
“Fairy” is suitable for racing, the “True X” structure, wheelbase only the 200mm, the 5 inch props.
Tail lights integrated 6 bright LED tail lights and the buzzer. LED tail lights support that FC (Betaflight / CleanFlight) control the color and the condition of the lights.
The biggest feature is in the nose of this frame, used the 3D TPU printing and the camera mount designed by 35 degree angle inclination. It can extremely reduce the wind resistance.
The sparrow, yes, he is called the sparrow. The sparrow is small all-sided.
GEP-MX is a mini frame. We call it little sparrows, small and flexible. Sparrow best apply 3nch blade, there will be two versions. GEP-MX3(True X) is suitable for all kinds of action, GEP-MSX (Stretch X) suitable for racing, Move very speed and flexibly.
Frame body ultralight use 3k carbon plate, thickness of 3 mm, combining aviation aluminum # 7075 fuselage, integral collocation, is very perfect. The pilot can be in a small space high-speed flight. Although small, but very resistant to fall off. It's worth noting that can perfect match RUNCAM Swift-Mini and Micro Swift lens. In order to let players precisely control their own flight Angle, our team used a laser carving scale, players can adjust Angle to his habit of flight, and we also radium vulture GEPRC anti-counterfeiting LOGO. Flight control pitch has two options, respectively is the commonly used 20 * 20 mm and 30.5 * 30.5 mm, The pilot can according to their own needs to be installed. Rack also equipped with LED taillights, available to the competition. Single stand about 39 g (do not include the electronic equipment). Clearly, he can make you amazing.
The sparrow, yes, he is called the sparrow. The sparrow is small all-sided.
GEP-MX is a mini frame. We call it little sparrows, small and flexible. Sparrow best apply 3nch blade, there will be two versions. GEP-MX3(True X) is suitable for all kinds of action, GEP-MSX (Stretch X) suitable for racing, Move very speed and flexibly.
Frame body ultralight use 3k carbon plate, thickness of 3 mm, combining aviation aluminum # 7075 fuselage, integral collocation, is very perfect. The pilot can be in a small space high-speed flight. Although small, but very resistant to fall off. It's worth noting that can perfect match RUNCAM Swift-Mini and Micro Swift lens. In order to let players precisely control their own flight Angle, our team used a laser carving scale, players can adjust Angle to his habit of flight, and we also radium vulture GEPRC anti-counterfeiting LOGO. Flight control pitch has two options, respectively is the commonly used 20 * 20 mm and 30.5 * 30.5 mm, The pilot can according to their own needs to be installed. Rack also equipped with LED taillights, available to the competition. Single stand about 39 g (do not include the electronic equipment). Clearly, he can make you amazing.
The Foxeer line of antennas provides many different options for all FPV enthusiasts needs. If you're looking for a specific color, length, Left Hand Polarization, or Right Hand Polarization. These antennas can be used both on the Video Transmitter side, and the Video Receiver side.
“Pagoda 2” is based on Maarten Baert optimized circular polarized antenna, Produced by GEPRC customize a 5.8 G antenna, is the scope of its bandwidth of 500 MHZ (5.55 to 6.05 GHz). Structure consists of three layers of 1 oz copper foil embedded PCB, only 8 grams of weight,use special heat shrink packaging, solid, durable, and beautiful. PCB materials used 1.0 mm FR – 4, 1 oz copper foil.
Pagoda 2 has natural advantages, axis ratio is below 1.3, standing wave ratio of 1.2.Can be used for transmitting antenna and receiving antenna (transmit and receive all use pagoda2 antenna is better).
Main Features:
- 1200TVL HD image, 1280 ( H ) x 960 ( V ), 16:9 aspect ratio
- Built-in OSD and microphone for flight data display and more immersion respectively
- Compatible with various devices - PAL / NTSC switchable, 5 - 40V input voltage range