Keep your TX16 safe in style with the official RadioMaster zipper case. This zipper case can be put around the foam box that is always supplied with every TX16s and offers a convenient and safe way to transport your favorite transmitter.
This Radiomaster AG01 Full CNC Hall Gimbal Set was designed and tested for over a year. This set features both the Self-Centering Gimbal and the Throttle Gimbal.
BETAFPV Nano RF TX module is based on the ExpressLRS project, an open-source RC link for RC applications. ExpressLRS aims to achieve the best possible...
The M9N GPS has an UBLOX M9N module, IST8310 compass, tri-colored LED indicator, and a safety switch. There are 3 different connectors options for different purposes.
H-RTK F9P is the latest differential high-precision GNSS positioning system series from Holybro. This system provides multi-band RTK with fast convergence times and reliable performance, concurrent reception of GPS, GLONASS, Galileo and BeiDou, and fast update rate for highly dynamic and high volume applications with centimeter-accuracy. It uses a UBLOX F9P module, a IST8310 compass, and a tri-colored LED indicator. It also has a integrated safety switch for a simple and convenient operation.
H-RTK F9P is the latest differential high-precision GNSS positioning system series from Holybro. This system provides multi-band RTK with fast convergence times and reliable performance, concurrent reception of GPS, GLONASS, Galileo and BeiDou, and fast update rate for highly dynamic and high volume applications with centimeter-accuracy. It uses a UBLOX F9P module, a IST8310 compass, and a tri-colored LED indicator. It also has a integrated safety switch for a simple and convenient operation.
The Pixhawk® 5X is the latest update to the successful family of Pixhawk® flight controllers, based on the Pixhawk® FMUv5X Open Standard and the Pixhawk®...
The Vista was fully authorized by DJI and compatible with their HD FPV System. Even better, the Caddx Vista was engineered to be lighter and smaller than the DJI Air Unit Module and also comes with mounting holes for easier installation onto your quad!
A single-camera module, which has a quick-release design for convenient replacement. The FPV camera does not come with a back cover or coaxial cables installed.Does not come with Air Unit Module. Cable not included, this is the camera only.
The Caddx Polar Micro Camera is an FPV camera with a mega starlight sensor. The Caddx Polar has a minimum 720p 60fps image transmission, with a transmission range of up to 4km and a minimum end-to-end latency within 32 ms. The camera is compatible with Vista and Air Unit modules.
Enhance your UAV fleet with Precision Landing and target recognition features. Attach the IR-LOCK Sensor to your UAV, and place the MarkOne Beacon where you want to land. Great...
Compared with F4 AIO 35A FC, F722 FC’s firmware is upgraded from F411 to F722, providing a better performance capability and higher calculation speed, which...
The CADDX VISTA KIT Micro Version is a replacement for the DJI Air Unit. With a micro-sized 19x19 camera, the Caddx Air Unit has all the features and performance of the original.The CADDX VISTA KIT features an ultra-low-latency high-definition digital image transmission, 1080p/60fps video recording, and eight frequency channels, allowing eight pilots to fly simultaneously.Compatible with DJI's Digital FPV Goggles, CADDX VISTA KIT (Digital VTX + HD FPV Camera) provides amazingly clear video, low latency, and even a built-in 1080P/60 FPS DVR.
Pavo30 whoop quadcopter, a new concept of 3-inch pusher drone developed by BETAFPV, is going further in performance, durability and power with brand new power system. It’s...
A Holybro Telemetry Radio is a small, light and inexpensive open source radio platform that typically allows ranges of better than 300m “out of the box”). The radio uses open source firmware which has been specially designed to work well with MAVLink packets and to be integrated with the Mission Planner, Copter, Rover and Plane.
Introducing the Radiomaster R-Series! This R81 Nano Receiver (with Sbus Output) has 8 channels and is Frsky D8 compatible, offering a range suitable for both drone and RC modelers.
Introducing the Radiomaster R-Series! This R161 Sbus Receiver (with S.Port Output) has 16 channels and is Frsky D16 compatible, offering a range suitable for both drone and RC modelers.
Introducing the Radiomaster R-Series! This R168 PWM Receiver (with Sbus Output) has 16 channels and is Frsky D16 compatible, offering a range suitable for both drone and RC modelers.
The Caddx Nebula Nano V2 Digital FPV Camera Kit is an advanced video transmission module that supports a 5.8GHz digital video signal and 720p 60fps image transmission.
X-Knight 360 Carbon Frame Kit is an innovative, versatile and functional design frame that is is designed to work seamlessly with Insta ONE R Camera...
A replacement or spare antenna for the Caddx Vista Specifications Brand: Caddx FPV Variant: Standard 8cm / 15Cm Weight: 4 g Includes 1 x Caddx Vista...
Beta95X V3 is perfectly suitable for the SMO 4K action camera. With a built-in camera mount and a power cable, it's very convenient for out-of-the-box installation and power input for the camera. Combining with SMO 4K, pilots can get a stable & high-quality video while in FPV flight.
Adopts a brand-new innovative pusher frame design, the frame is made of PA12 material, which has high abrasion resistance and can dampen noise & vibrations, bringing the drone a more durable flight and no fear of damage. The frame also comes with an EVA foam cushioning design to give you more safety flying.
Equipped with F4 AIO 20A Toothpick FC V4, 1106 3800KV motor, and D63 5-blade props, this highly efficient power system keeps Beta95X V3 more powerful and less noise in flight. For the battery, we highly recommend you using BETAFPV 450mAh 4S battery to get the best flying experience.
Centering the drone's gravity by reversed-motor design and top battery place makes the drone more maneuverable to achieve all FPV freestyle tricks such as diving.
Further improves the shock mitigation system to eliminate the shake of the camera, Beta95X V3 will make the camera more stable on the flight, which ensures pilots can capture all the beautiful moments of flight with the stabilized and clear video.
Flight time: About 4.5 min flight with 450mAh 4S battery
BETAFPV SMO 4K Camera
SMO 4K camera, a high-degree lightweight action camera for FPV drones that is developed by BETAFPV using Insta360 technology. SMO 4K camera only weighs 30g and perfectly fit for FPV drones, and brings pilots an extraordinary flying experience and a strong visual impact. What's more, it almost compatible with all kinds of FPV drones like micro cinewhoop Beta95X V3, 3-4in the ducted quad, 4-5in long-range FPV drone, and fixed-wing. It will be the perfect action camera for pilots in search of high-quality video with FPV racing drones.
Beta95X V3 Pusher Frame
A newly designed pusher whoop frame - Beta95X V3 Frame is made of high-quality PA12 material, which can dampen noise and vibrations and have high abrasion resistance, bringing the drone a more durable flight and no fear of damage. Meanwhile, it also comes with an EVA foam cushioning design to give you more safety flying. The pusher style puts all the cameras and batteries on the top of the platform, makes the center of gravity is right in the middle of the drone, brings the best fly operability.
Camera
Customized EOSV2 micro FPV camera is also provided on Beta95X V3 Whoop Quadcopter, brings a high-quality video and low RF interference.
FC & ESC
Beta95X V3 series whoop drone is equipped with the new released F4 20A AIO toothpick brushless FC, it extremely reduces the weight while improving the ability of the ESC to continuous current 20A, and brings pilots more power to fly the Beta95X V3 quad! Meanwhile, the new 20A FC V4 adds 2 pin connector ports for DJI Digital VTX and Rx, just plug & play, less solder work needed, super easy to install.
Motor & Props
Gemfan D63 5-Blades Props is designed for the inverted installation, and it brings pilots a smooth flight! Meanwhile, compared with D63 3-blades propellers, D63 5-blade props are more durable and more powerful, offers pilots a high-efficiency flight experience. Equipped with the 1106 3800KV Brushless Motor, it brings a stronger power and lower noise, which will give pilots an unprecedented flying experience.
The Beta95X V3 Whoop Quadcopter also comes with "props out" by default. Why we need "Props out" direction?
Default Betaflight props direction, quadcopter dips, and "washes out" in hard corners. With reversed props or "props out", no more dipping even in the hardest cornering.Know more about "Props Out".
FAQ
1. Cli Dump of Beta95X V3 Whoop Quadcopter (Click here to find the details.)
2. STL File for the Base of Naked Camera for Beta95X V3 Pusher Drone Series (Click here to find the details.)
3. How to power the Naked Camera on Beta95X V3 or Beta95X V3 HD Digital VTX.
One adapter 3P GH1.25 power cable for Customized Naked Camera is offered in the package, pilots can use it to power the Naked Camera.
Package
1 * Beta95X V3 Whoop Quadcopter
1 * Gemfan D63 5-blades Propellers(2CW+2CCW)
1 * 20mm FPV Camera Mount
1 * Spare EVA Foam Tape
1 * USB Adapter Board for FC
1 * Adapter Cable for Customized Naked Camera
Batteries and SMO 4K Camera are not included in the package. You can get it here for 450mAh 4S battery and SMO 4K camera.***Without VTX)***
The HGLRC Forward 65A 4-in-1 ESC brings serious power to the 30.5x30.5 game. 3-6S capable and stackable with other mini FC's, this ESC gives you great specs in a tiny package.
Herelink AccessoriesHerelink is an all-in-one solution for long-range HD video transmission, which can realize video, data transmission and radio control. The 2.4GHz radio controller with built-in screen...
*BNF/PNP Version Include: HGLRC Sector 5 V3 Freestyle FPV Racing Drone Net Weight:442.4g(Weight without receiver) Sector 5 V3 Freestyle Frame 5 inch Type:5″ frame Wheelbase:218mm...
Mini Carrier Board has the standardized DF17 connector which allows user to connect it to every version of the Cube flight controller. With smaller size...
Holybro Kakute F7 HDV is designed to work with the DJI FPV VTx module. The GH port available on the board makes it much more convenient for you to connect Holybro Kakute F7 HDV to the DJI FPV VTx, for both signal and power supply.
This mini camera provides some incredible specs for 1200TVL resolution and WDR worldwide. EOS2 is equipped with 1/3 CMOS sensor and 2.1mm lens with a 16:9 projection ratio.This camera is well suited to micro-structures that requires maximum weight and space Reduction without compromising quality.
I want freestyle frame to show more performance in flight,a Super lightweight Freestyle frame,more convenient installation of electronic devices and more balanced center of gravity, so as to achieve better Smooth flight shooting, These ideas build the freestyle frame Mark4.
Get Started on your road to Autonomy! This Kit contains the following items The Cube…. the brains behind the opperation. A standard carrier board.(no compatible...
INSIDE THE CUBE An STM32F427 Rev 3 Flight management unit. (where the flight controller lives.) An STM32F100 I/O processor with pass through capabilities for...
Cube Yellow target to education, drones lovers and professional cost-effective flight control hardware providers. The new generation of more powerful F7 processor, stronger performance, faster,...
The NEO-M8 is optimized for cost sensitive applications, while NEO-M8N and NEO-M8Q provide best performance and easier RF integration. The NEO form factor allows easy migration from previous NEO generations. Sophisticated RF-architecture and interference suppression ensure maximum performance even in GNSS-hostile environments.
What’s inside Here+ RTK Base & HERE 3 (M8P) Combo (Separated products) Highlights Centimeter‑level GNSS positioning for the mass market Integrated Real Time Kinematics (RTK)...
Pixhawk ® 4 is the latest update to the successful family of Pixhawk flight controllers. It is designed and developed in collaboration with Holybro and...
This is a frame designed for Freestyle, called “Mark2”. After repeated design adjustment and testing, finally finished, let us present to you.
Although Mark2 is a regular rectangular frame, it still wants you to know its design features. A lot of mechanical shapes are added to the design, and the whole is very sexy and science fiction. The four arm and aluminum alloy parts are fixed, easy to replace the new machine arm, and the fixed performance is good. The camera position can be very good to protect the camera from damage
High-precision CNC aluminum alloy fixed parts, 3K full carbon fiber, 12.9 level YFS screw, give Mark2 to maintain strength advantage.
Enjoy Freestyle.
GEP-GR2306 is the enamored production of our GEPRC. It passes our performance test in all aspects, and it can meet our extreme requirement on the parameter of the appearance of the electrical machine totally. Its elaborate appearance processing makes our eyes light up and we believe that the strong and steady power take-off will meet your expectation.
Our team keeps thinking that how to make a rack which is balanced both in competition and freestyle. Perhaps, GEP-KX5 can make you feel the good balance by its new and fresh design.GEP-KX5 is wished to be designed as a rack which is quite elegant and graceful. This is the reason why it is named as “Elegant”.
GEP-GR1408 motor is GEPRC’s newly developed brushless motor specially designed for 3inch propeller, a highly efficient and powerful motor, incorporating many new features and quality material throughout and is available in three versions - 3500kv, 3750K and 4100Kv to cater to the most demanding of flyers.
The GEP-GR1408 motor features a new streamlined motor shape, offering ultra-low wind resistance for fast forward flight and efficient heat dissipation. Incorporating high performance N52H curved magnets with a stator to magnet air-gap of only 0.15mm, the GEP-GR1408 motor is capable of high torque. High temperature resistance and low current resistant #180 enameled wire stator coil ensures stable power output throughout the throttle range and further enhanced by durable smooth running NSK Japanese bearings. The high precision CNC machined #7075 aluminum shaft increases crash durability of this motors while the large ventilation slots in the bell keeps the motor temperature low.
The GEP-GR1408 motor is optimized for 4S lipo and designed especially for 3inch propellers and when used with the GEPRC 3042 triblade propellers, it provides high output efficient performance. At only 15.2 g, the 4100Kv version generates an amazing 482g. The GEP-GR1408 motor is available in both CCC and CW threaded shaft.
GEP-IX5, is our new frame, called “Fairy”. 5 inch props, wheelbase is 200mm.
“Fairy” is suitable for racing, the “True X” structure, wheelbase only the 200mm, the 5 inch props.
Tail lights integrated 6 bright LED tail lights and the buzzer. LED tail lights support that FC (Betaflight / CleanFlight) control the color and the condition of the lights.
The biggest feature is in the nose of this frame, used the 3D TPU printing and the camera mount designed by 35 degree angle inclination. It can extremely reduce the wind resistance.
The sparrow, yes, he is called the sparrow. The sparrow is small all-sided.
GEP-MX is a mini frame. We call it little sparrows, small and flexible. Sparrow best apply 3nch blade, there will be two versions. GEP-MX3(True X) is suitable for all kinds of action, GEP-MSX (Stretch X) suitable for racing, Move very speed and flexibly.
Frame body ultralight use 3k carbon plate, thickness of 3 mm, combining aviation aluminum # 7075 fuselage, integral collocation, is very perfect. The pilot can be in a small space high-speed flight. Although small, but very resistant to fall off. It's worth noting that can perfect match RUNCAM Swift-Mini and Micro Swift lens. In order to let players precisely control their own flight Angle, our team used a laser carving scale, players can adjust Angle to his habit of flight, and we also radium vulture GEPRC anti-counterfeiting LOGO. Flight control pitch has two options, respectively is the commonly used 20 * 20 mm and 30.5 * 30.5 mm, The pilot can according to their own needs to be installed. Rack also equipped with LED taillights, available to the competition. Single stand about 39 g (do not include the electronic equipment). Clearly, he can make you amazing.
The sparrow, yes, he is called the sparrow. The sparrow is small all-sided.
GEP-MX is a mini frame. We call it little sparrows, small and flexible. Sparrow best apply 3nch blade, there will be two versions. GEP-MX3(True X) is suitable for all kinds of action, GEP-MSX (Stretch X) suitable for racing, Move very speed and flexibly.
Frame body ultralight use 3k carbon plate, thickness of 3 mm, combining aviation aluminum # 7075 fuselage, integral collocation, is very perfect. The pilot can be in a small space high-speed flight. Although small, but very resistant to fall off. It's worth noting that can perfect match RUNCAM Swift-Mini and Micro Swift lens. In order to let players precisely control their own flight Angle, our team used a laser carving scale, players can adjust Angle to his habit of flight, and we also radium vulture GEPRC anti-counterfeiting LOGO. Flight control pitch has two options, respectively is the commonly used 20 * 20 mm and 30.5 * 30.5 mm, The pilot can according to their own needs to be installed. Rack also equipped with LED taillights, available to the competition. Single stand about 39 g (do not include the electronic equipment). Clearly, he can make you amazing.
“Pagoda 2” is based on Maarten Baert optimized circular polarized antenna, Produced by GEPRC customize a 5.8 G antenna, is the scope of its bandwidth of 500 MHZ (5.55 to 6.05 GHz). Structure consists of three layers of 1 oz copper foil embedded PCB, only 8 grams of weight,use special heat shrink packaging, solid, durable, and beautiful. PCB materials used 1.0 mm FR – 4, 1 oz copper foil.
Pagoda 2 has natural advantages, axis ratio is below 1.3, standing wave ratio of 1.2.Can be used for transmitting antenna and receiving antenna (transmit and receive all use pagoda2 antenna is better).
Hawk, The dive speed of the prey is exciting.
This is the Hawk, The model name is GEP-RX5. Wheelbase 210mm, can be used for 5 inch propeller. “True X”Structure. This design is not difficult to see that the first two and two arm arm horizontal staggered, this helps to reduce turbulence, increase the efficiency of wind suction impeller.Gopro elements can be adjusted to adjust the range of 20-50 degrees, the lens is perfect support Hs1177, Hs1190, swift, Plus OWL and other most lenses. Lens distance 28mm. A reasonable layout, the factory comes with 10 WS2812B lights, support the microcontroller or flight control. Motor protection like a fish, to protect the motor to a certain extent, very good. Whole machine using YFS screws, the factory comes with a golden version. Random comes with BEC, 5V/12V PDB output. Save most of the time the player.
GEP-TSX5 is made of 3K Carbon Fiber Quadcopter Frame plates and the Grand 12.9 YFS screw. The Stretch-X made it more adapted to the Racing. Our design teams decide to use 5mm(thickness) x 9mm(width) Arm to overcome wind resistance effectively. The motor seat is redesigned to a large extent to protect the motor. The camera seat works for most brands, Such as Runcam swift /swift2, Foxeer HS1190 and so on. The camera 20 to 60 degress. But I’d like to introduce the GoPro. 35-58 degress. Applies to most scenarios. Such as Racing and Freestyle.
The leopard, natural predators, running at a staggering rate
This is GEP - LSX5, Leopard(GEP-LX) derivatives, ‘S’ mean is stretching. This is more suitable for competition. High-speed forward flight and rapid roll have more advantages. GEP-LSX respectively with three kinds of specifications.GEP-LSX4 wheelbase 205 mm, suitable for 4inch propeller. GEP-LSX5 wheelbase 230 mm, suitable for 5inch propeller, GEP-LSX6 wheelbase 265 mm for 6inch propeller.
The frame use 3k ultra-light carbon plate + Aviation aluminum # 7075 body. To strengthen the four arm, we also design a fixed four arm of the aluminum alloy parts, it is not easy to make the machine arm shift.
We also equipped with A piece of PDB, take BEC output 5 v 3 A and 12V 0.5A.The frame all adopt the YFS screws, 12.9 magnitude
The leopard, natural predators, running at a staggering rate.
This is the GEP-LX, also called ‘Leopard’, There are three kinds of specifications respectively. 4inch(wheelbase 195mm), 5inch(wheelbase 220mm), 6inch(wheelbase 255mm). The fuselage low center of gravity design.