The M9N GPS has an UBLOX M9N module, IST8310 compass, tri-colored LED indicator, and a safety switch. There are 3 different connectors options for different purposes.
H-RTK F9P is the latest differential high-precision GNSS positioning system series from Holybro. This system provides multi-band RTK with fast convergence times and reliable performance, concurrent reception of GPS, GLONASS, Galileo and BeiDou, and fast update rate for highly dynamic and high volume applications with centimeter-accuracy. It uses a UBLOX F9P module, a IST8310 compass, and a tri-colored LED indicator. It also has a integrated safety switch for a simple and convenient operation.
H-RTK F9P is the latest differential high-precision GNSS positioning system series from Holybro. This system provides multi-band RTK with fast convergence times and reliable performance, concurrent reception of GPS, GLONASS, Galileo and BeiDou, and fast update rate for highly dynamic and high volume applications with centimeter-accuracy. It uses a UBLOX F9P module, a IST8310 compass, and a tri-colored LED indicator. It also has a integrated safety switch for a simple and convenient operation.
The Pixhawk® 5X is the latest update to the successful family of Pixhawk® flight controllers, based on the Pixhawk® FMUv5X Open Standard and the Pixhawk®...
The Vista was fully authorized by DJI and compatible with their HD FPV System. Even better, the Caddx Vista was engineered to be lighter and smaller than the DJI Air Unit Module and also comes with mounting holes for easier installation onto your quad!
A single-camera module, which has a quick-release design for convenient replacement. The FPV camera does not come with a back cover or coaxial cables installed.Does not come with Air Unit Module. Cable not included, this is the camera only.
The Caddx Polar Micro Camera is an FPV camera with a mega starlight sensor. The Caddx Polar has a minimum 720p 60fps image transmission, with a transmission range of up to 4km and a minimum end-to-end latency within 32 ms. The camera is compatible with Vista and Air Unit modules.
Enhance your UAV fleet with Precision Landing and target recognition features. Attach the IR-LOCK Sensor to your UAV, and place the MarkOne Beacon where you want to land. Great...
The CADDX VISTA KIT Micro Version is a replacement for the DJI Air Unit. With a micro-sized 19x19 camera, the Caddx Air Unit has all the features and performance of the original.The CADDX VISTA KIT features an ultra-low-latency high-definition digital image transmission, 1080p/60fps video recording, and eight frequency channels, allowing eight pilots to fly simultaneously.Compatible with DJI's Digital FPV Goggles, CADDX VISTA KIT (Digital VTX + HD FPV Camera) provides amazingly clear video, low latency, and even a built-in 1080P/60 FPS DVR.
A Holybro Telemetry Radio is a small, light and inexpensive open source radio platform that typically allows ranges of better than 300m “out of the box”). The radio uses open source firmware which has been specially designed to work well with MAVLink packets and to be integrated with the Mission Planner, Copter, Rover and Plane.
The Caddx Nebula Nano V2 Digital FPV Camera Kit is an advanced video transmission module that supports a 5.8GHz digital video signal and 720p 60fps image transmission.
A replacement or spare antenna for the Caddx Vista Specifications Brand: Caddx FPV Variant: Standard 8cm / 15Cm Weight: 4 g Includes 1 x Caddx Vista...
The HGLRC Forward 65A 4-in-1 ESC brings serious power to the 30.5x30.5 game. 3-6S capable and stackable with other mini FC's, this ESC gives you great specs in a tiny package.
Frame Diagram Link Roma F5 DJI Intro Roma F5 DJI Frame: Wheelbase :226mm Weight :135g Prop Siza :5 inch FC Mounting: 30.5×30.5(M3)&20×20mm(M2) Motor Mounting:16mm Top...
The best drone backpack for DJI Mavic series and foldable drones. Specially designed for the DJI Mavic series backpack turns easily from a daypack into...
TAYCAN 25 Frame Kit Specification Frame Diagram Link Wheelbase :125mm Weight :86g Prop Siza :2.5 inch FC Mounting:20×20&25.5×25.5m(M2) Motor Mounting:9mm&12mm Top Plate 1.5mm Bottom Plate...
FETtec Spike Absorber well-selected TVS diodes to absorb dangerous voltage spikes to protect connected components designed for use with an electrolytic capacitor, which can be...
Features: Active current limiting @ 45A Input voltage: 3S-6S High quality 40V MOSFETs STM32G071 @ 64MHz 128 kHz Motor PWM Full sine wave control Soldering...
Features: Graphic OSD (STM32) Full KISS Tuning Filter (PIDs, Rates, Settings) LED control (RGB LED, Racewire) VTX Live data graphs (Voltage, motor rpm, current, motor...
Herelink AccessoriesHerelink is an all-in-one solution for long-range HD video transmission, which can realize video, data transmission and radio control. The 2.4GHz radio controller with built-in screen...
*BNF/PNP Version Include: HGLRC Sector 5 V3 Freestyle FPV Racing Drone Net Weight:442.4g(Weight without receiver) Sector 5 V3 Freestyle Frame 5 inch Type:5″ frame Wheelbase:218mm...
Mini Carrier Board has the standardized DF17 connector which allows user to connect it to every version of the Cube flight controller. With smaller size...
Holybro Kakute F7 HDV is designed to work with the DJI FPV VTx module. The GH port available on the board makes it much more convenient for you to connect Holybro Kakute F7 HDV to the DJI FPV VTx, for both signal and power supply.
This mini camera provides some incredible specs for 1200TVL resolution and WDR worldwide. EOS2 is equipped with 1/3 CMOS sensor and 2.1mm lens with a 16:9 projection ratio.This camera is well suited to micro-structures that requires maximum weight and space Reduction without compromising quality.
The OmniNXT F7 is Airbot’s top of the range flight controller based on the newly designed NXT architecture. It uses the trusty MPU6000 Gyro with an additional ICM20608 on top. With the onboard damping box, the gyros run perfectly under 32k looptime. If you haven't already seen it, you should check out Josh's awesome video on different IMUs. The NXT also comes with 2 different BECs and 6 UARTs.
FIRMWARE TARGET : MAMBA F722 (LEGACY) Diagram Link From Help Centre Link Note:Because STM32F722 heat large , please leave at least 5mm interspace at both sides of...
I want freestyle frame to show more performance in flight,a Super lightweight Freestyle frame,more convenient installation of electronic devices and more balanced center of gravity, so as to achieve better Smooth flight shooting, These ideas build the freestyle frame Mark4.
Get Started on your road to Autonomy! This Kit contains the following items The Cube…. the brains behind the opperation. A standard carrier board.(no compatible...
INSIDE THE CUBE An STM32F427 Rev 3 Flight management unit. (where the flight controller lives.) An STM32F100 I/O processor with pass through capabilities for...
Cube Yellow target to education, drones lovers and professional cost-effective flight control hardware providers. The new generation of more powerful F7 processor, stronger performance, faster,...
The NEO-M8 is optimized for cost sensitive applications, while NEO-M8N and NEO-M8Q provide best performance and easier RF integration. The NEO form factor allows easy migration from previous NEO generations. Sophisticated RF-architecture and interference suppression ensure maximum performance even in GNSS-hostile environments.
What’s inside Here+ RTK Base & HERE 3 (M8P) Combo (Separated products) Highlights Centimeter‑level GNSS positioning for the mass market Integrated Real Time Kinematics (RTK)...
Pixhawk ® 4 is the latest update to the successful family of Pixhawk flight controllers. It is designed and developed in collaboration with Holybro and...
The Omnibus Fireworks flight controller uses the ICM20608 over SPI for the best possible flight performance. With onboard damping box, the ICM20608 runs perfectly under 32k Gyro loop. If you haven't already seen it, you should check out Josh's awesome video on different IMUs. Also onboard are a barometer and AB7456 OSD chip for the BetaFlight integrated OSD.
This is a frame designed for Freestyle, called “Mark2”. After repeated design adjustment and testing, finally finished, let us present to you.
Although Mark2 is a regular rectangular frame, it still wants you to know its design features. A lot of mechanical shapes are added to the design, and the whole is very sexy and science fiction. The four arm and aluminum alloy parts are fixed, easy to replace the new machine arm, and the fixed performance is good. The camera position can be very good to protect the camera from damage
High-precision CNC aluminum alloy fixed parts, 3K full carbon fiber, 12.9 level YFS screw, give Mark2 to maintain strength advantage.
Enjoy Freestyle.
GEP-GR2306 is the enamored production of our GEPRC. It passes our performance test in all aspects, and it can meet our extreme requirement on the parameter of the appearance of the electrical machine totally. Its elaborate appearance processing makes our eyes light up and we believe that the strong and steady power take-off will meet your expectation.
Our team keeps thinking that how to make a rack which is balanced both in competition and freestyle. Perhaps, GEP-KX5 can make you feel the good balance by its new and fresh design.GEP-KX5 is wished to be designed as a rack which is quite elegant and graceful. This is the reason why it is named as “Elegant”.
GEP-GR1408 motor is GEPRC’s newly developed brushless motor specially designed for 3inch propeller, a highly efficient and powerful motor, incorporating many new features and quality material throughout and is available in three versions - 3500kv, 3750K and 4100Kv to cater to the most demanding of flyers.
The GEP-GR1408 motor features a new streamlined motor shape, offering ultra-low wind resistance for fast forward flight and efficient heat dissipation. Incorporating high performance N52H curved magnets with a stator to magnet air-gap of only 0.15mm, the GEP-GR1408 motor is capable of high torque. High temperature resistance and low current resistant #180 enameled wire stator coil ensures stable power output throughout the throttle range and further enhanced by durable smooth running NSK Japanese bearings. The high precision CNC machined #7075 aluminum shaft increases crash durability of this motors while the large ventilation slots in the bell keeps the motor temperature low.
The GEP-GR1408 motor is optimized for 4S lipo and designed especially for 3inch propellers and when used with the GEPRC 3042 triblade propellers, it provides high output efficient performance. At only 15.2 g, the 4100Kv version generates an amazing 482g. The GEP-GR1408 motor is available in both CCC and CW threaded shaft.